Electrical Options

  • Hand Operated NEMA 12 - control with an 8′ cord is standard
  • Hand Operated NEMA 4 - weather resistant control with an 8′ cord. Substituted for NEMA 12 Additional controller
  • NEMA - 1 foot control - foot operated control substituted for NEMA 12 Hand Control Additional controller
  • Wall Mounted Control
  • Limit Switch - Limits the vertical travel of the scissor lift.
  • Pedestal Mounted Controls - NEMA 12 controller mounted on a rugged steel stand with momentary push buttons
  • Velocity Fuse - standard safety feature on all Presto Scissor lifts prevents the unit from collapsing in the event of a hydraulic pressure loss.
  
 

lift table Options

Hydraulic Options

  • External / Remote Power Units - all three phase units include transformer for low voltage control, 6′ of hose and a mounting stand.
  • 1 HP Single Phase - (115-230v/1/60)
  • 1½ HP Three Phase - (208, 220 or 460/3/60)
  • External 5 HP Three Phase - (208, 220 or 460/3/60)
  • 1½ HP Three Phase - (575/3/60)
  • Air Motors
  • Custom Designed
  • Fire Resistant Hydraulic Fluid - water-glycol fluids are fire resistant, non-explosive and non-toxic. Approved by Factory Mutual Insurance Engineering Laboratories
  • Low Temp Oil
 
 
 

Mechanical Options

  • Oversized Platforms - platforms can be increased in width and length up to additional 24″. Side and end load capacities are derated 2% per inch of increase and oversized models must be lagged to the floor.
  • Platform with Beveled Edges - welded at 30° angles, increased the standard platform by 4″ on all sides
  • Electro-Mechanical Toe Guard - mounted to the under side of the platform, adds 4″ on all sides
  • Pit Mounted Units - for ground level applications require either a platform with Beveled Edges or Electro-Mechanical Toe Guards. Lifting Eyes required for installation and External Motor recommended.
  • Lifting Eyes - provided for installation and transporting of unit with a sling or lifting chain
  • Portable Units - wheeled dolly handle and two 5″ fixed wheels (specify side or end mounting) for moving empty lifts. Overall lowered height is not changed when unit is in an operating position. XL models X3W and X4W models Oversized Platform & other models
  • Transportable Units - 6″ steel casters, two fixed and two swivel, and a Presto floor lock mounted underneath base frame. Adds 10¼″ to the lowered height XL models X3W and X4W models Oversized Platform & other models
  • V Grooved Wheels - 5″ steel wheels for Transportable Units only, sold per pair.
  • Fork Pockets - used for moving scissor lifts between work stations.
  • Ball Transfer Tops - for multi directional movement of work loads, available for all load weights. Adds 2″ to overall lowered height.
  • Turntables - constructed of ½″ steel plate and mounted on a 24″ x 24″ base plate equipped with a pivot pin captured bearing and four 1¾″ cam followers. Base has mounting holes for lagging unit to table top, floor stand, floor mounting available. Capacities
  • Turntables - Capacities conform to desired work load. Note: Turntables add 2¾″ to overall height. 36″ round, shipping weight 200 lbs 36″ square, shipping weight 225 lbs 48″ round, shipping weight 350 lbs 48″ square, shipping weight 380 lbs
  • Detent Stops - Spring activated stops for a Turntable, standard stops positioned at 90° increments Spring
  • Conveyor Top - mounted to the lift table platform these 1.9″ diameter rollers on 3″ center have a 1000 lb capacity per linear foot. Adds 4″ to overall height 24″ x 36″ platform 24″ x 48″ platform 24″ x 64″ platform Custom sizes and designs available
  • Conveyor Sides - used to retain product on conveyor tops, recommend on all Transporting Units. Fixed 3″ sides Movable 3″ sides
  • Optional Top Material - for special handling of loads, v tops, aluminum material, stainless steel, diamond plate, etc.
  • Accordion (bellow) Skirts - designed to cover to scissor leg assemble of the lift table. XL 24 Series SL 36 Series SL 48 Series Other Models